Item # 6526-24000, Nylon 6 Cast Rod On Trident Plastics, Inc.

Request Information

Cast Nylons are a range of polyamides produced by a casting process involving the anionic polymerisation of caprolactum. This process allows the production of semi-finished plate, rod, tube and custom castings that are largely free of internal stresses. Natural Cast Nylon is the basic grade from which all other grades of Cast Nylons stem. Generally accepted as the primary engineering polymer, Natural Cast Nylon is suitable for virtually any plain bearing application not to mention a huge rangemore

Unit of Measure

Specifications
Material Specifications

Material	N/A PA6
Color	N/A HS Blue
Diameter	N/A 24.00
Weight	N/A 241.2 lb/ft
Standard Length	N/A 1M ft2' ft4' ft
Specific Gravity (ASTM D792)	N/A 1.15 - 1.17
Hardness - Rockwell (ASTM D785)	N/A R115 - R125
Water Absorption - Saturation (ASTM D570)	N/A 5.0 - 6.0 %
Tensile Strength (ASTM D638)	N/A 10000 - 13500 psi
Tensile Modulus (ASTM D638)	N/A 400000 - 550000 psi
Flexural Strength	N/A 15500 - 17500 psi
Flexural Modulus	N/A 420000 - 500000 psi
Impact Strength, Notched at 73°F (ASTM D256)	N/A 0.70 - 0.90 ft·lb/in
Dynamic Coefficient of Friction at 40 psi, 50 fpm	N/A 0.22
Wear Factor Against Steel - 40 psi, 50 fpm	N/A 200 x 10^-10 in³/hr
Coefficient of Linear Thermal Expansion	N/A 5 x 10^-5 in/in/ºF
Heat Deflection Temperature at 66 psi	N/A 400 - 430 ºF
Heat Deflection Temperature at 264 psi	N/A 200 - 400 ºF
Maximum Operating Temp. - Short Term	N/A 330 ºF
Maximum Operating Temp. - Long Term	N/A 230 ºF
Dielectric Strength (ASTM D149)	N/A 500 - 600 V/m
Flammability Rating (UL 94)	N/A HB
Availability	N/A stock

N/A Cast Nylon/Type 6 (Nylon 6)
This unmodified Type 6 Nylon offers the highest strength and hardness of the Cast Nylon grades. Natural, Black, Blue and custom colors also available Meets or exceeds ASTM D5989 S-PA0211. LP-410A

Blue Cast Nylon/Type 6 - Heat Stabilized
Meets or exceeds ASTM D5989 S-PA0231.

Cast Nylon MD/Type 6 - Wear Resistant (MoS2 Filled)
This "Filled" Cast Nylon contains finely divided particles of Molybdenum Disulphide (MoS2) to enhance its load bearing capabilities while maintaining the impact resistance inherent to Nylon. It is the most commonly used grade for gears, sheaves, sprockets and custom parts. It is Gray - Black in color. Meets or exceeds ASTM D5989 S-PA0221. LP-410A Wear Resistant

Cast Nylon MD+Oil/Type 6 (Oil-Impregnated - MoS2 Filled)
This grade combines Molybdenum Disulphide and Oil for the load capacity, plus improved frictional characteristics. It excels in higher pressures, and at low speeds-up to 40 fpm. It offers 20% lower coeficient of friction, 50% greater limiting PV, and a lower "k" factor than Cast Nylon MD, and the lowest "slip-stick" of any Nylon product making it ideal for slide pads, thrust washers and trunion bearings. Cast Nylon MD+Oil is available in Dark Blue & Gray.

Oil-Impregnated CAST NYLON - GREEN/TYPE 6
Meets or exceeds ASTM D5989 S-PA0251.

Material

Color

Diameter

Weight

Standard Length

Specific Gravity (ASTM D792)

Hardness - Rockwell (ASTM D785)

Water Absorption - Saturation (ASTM D570)

Tensile Strength (ASTM D638)

Tensile Modulus (ASTM D638)

Flexural Strength

Flexural Modulus

Impact Strength, Notched at 73°F (ASTM D256)

Dynamic Coefficient of Friction at 40 psi, 50 fpm

Wear Factor Against Steel - 40 psi, 50 fpm

Coefficient of Linear Thermal Expansion

Heat Deflection Temperature at 66 psi

Heat Deflection Temperature at 264 psi

Maximum Operating Temp. - Short Term

Maximum Operating Temp. - Long Term

Dielectric Strength (ASTM D149)

Flammability Rating (UL 94)

Availability